|
 |
|
 |
|
|
|
| Home - Fax Repair - Error Codes - Fax Features |
|
|
|
|
Laser Printer Repair |
Panasonic Error Codes001 recording paper jam002 recording paper jam 010 no recording paper 014 print cartridge is not attached 015 out of ink 017 wrong paper size 030 document misfeed 031 document jammed or exceeds maximum length (2 meters) 039 during dialing, STOP was pressed 041 out of toner 045 no toner cartridge 060 a cover or door is open 061 a cover or door is open 063 jam access cover is open 316 clean the ink station overflow tray and encoder strip on inkjet models 400 during initial handshake, RX station did not respond; comm error 403 no polling capability at remote side 404 during initial handshake a comm error occurred 405 during initial handshake a comm error occurred 406 password mismatch 407 no confirmation from the RX station for the previous page sent 408 remote side confirmation of previous page is illegible 409 remote side confirmation of previous page is illegible 411 polling password does not match 412 no data from the transmitting side 414 polling password does not match 415 polling transmission error 416 received data has too many errors 417 received data has too many errors 418 received data has too many errors 419 received data has too many errors 420 machine enters RX mode but receives no command from TX side (not a fax calling) 422 interface is not compatible 427 interface is not compatible 430 comm error occurred while receiving 434 comm error occurred while receiving 436 received data has too many errors 456 memory overflow on confidential document or relay request 490 received data has too many errors 492 comm error occurred while receiving 493 comm error occurred while receiving 494 comm error occurred while receiving 495 telephone line disconnected 540 comm error occurred while transmitting 541 comm error occurred while transmitting 542 comm error occurred while transmitting 543 comm error occurred while transmitting 544 comm error occurred while transmitting 550 telephone line disconnected 552 comm error occurred while receiving 553 comm error occurred while receiving 554 comm error occurred while receiving 555 comm error occurred while receiving 580 sub-address TX to a unit without sub-address function 581 sub-address TX to a unit without sub-address function 601 ADF misfeed 623 no document was on the ADF 630 redial unsuccessful (busy line or no response) 634 redial unsuccessful (busy line or no response) 631 during dailing, STOP was pressed 638 power failure occurred during the communication 640 telephone off hook after comm is completed 870 memory overflow while storing TX documents 879 memory overflow while storing RX documents 975 DRAM parity error (document info in memory is lost, very common, also clean encoder strip) Extremely reliable machines. The Panafax inkjet models often have an HP counterpart (and use the same inkjet cartridge). After changing fax parameters, always cycle the power. The error code list on the HP page at this site typically applies to Panasonic fax machines as well. Panasonic PX-350 ram clear Press # 7 dial dial dial dial * 6 enter Press up-arrow key until the display reads shipment set then press start The display will read reset counter Select yes or no then press start Press # 7 dial dial dial dial * 3 enter to print a full parameter list. To clean the optics, remove the black plastic access panel below scanner glass. Panasonic PX-360 ram clear Press standby set dial dial dial dial * 6 start 9 9 On success, a long beep will be heard Panasonic UF-321 ram clear (same as HP-900 and most Panasonic's) Press menu 7 dial dial dial dial * 6 start Press up-arrow key until the display reads shipment set then press start The display will read reset counter Select yes or no then press start Ozone filter alarm reset Press menu 7 4 set 6 4 set clear set stop (these instructions come with the replacement filter) UF-550/560/770/880 ram clear Press monitor instead of dial (otherwise same procedure as with UF-321 above) Parameter 65 for memory collation should be set to invalid to maximize the memory page rating |
 |
 |
|
Denver Colorado PHP Programmer Web Developer Resume
:::